Premetto che il seguente post l'ho gia inserito alla sezione "Schede Madri" ma non sapendo qual'è il posto + adatto lo posto anche qui!!
Ho provato ad abilitare la seguente voce nella mia scheda e dopo il riavvio non ha + dato segni di vita...:(
Come posso fare x disabilitare la seguente cosa..c'è un modo.
Premetto che la scheda era settata prima a 105/34 e ora, anche se non si accenda è a 133/33, ma se le mie memorie vano a 133 xchè non va +??
Si riescono a trovare le memorie da 6ns come dice sotto il messaggio x provare a ripristinare la vecchia configurazione.
3.9.1 CPU Host/PCI Clock
The item is set the CPU Host/PCI Clock. The Default setting is recommended.
Any attempts to push beyond product specification are not recommended.
You must install suitable SDRAM on board when the setting is changed. For example, you must install 8ns or faster SDRAM on board if you set 102/34 ~ 120/40MHz as external frequency and must install 7ns or faster SDRAM on board if you set 133/33 ~ 140/35MHz as external frequency. If the external frequency is 143/36 ~ 150/38MHz, you must have installed 6ns or faster SDRAM on board.
resettando il bios non torna tutto ok?
Purtroppo lo schermo è tutto nero, il bios non parte!
si ma il bios lo resetti via jumper sulla scheda madre non dal bios.... guarda sul manuale dove si trova il CMOS reset oppure togli la pila per 5 minuti e poi reinseriscila e vedi se si accende!!
OK, IN EFFETTI è LA STESSA COSA CHE MI HA DETTO UNA PERSONA, CIOè RESETTARE IL BIOS TOGLIENDO LA PILA E FACENDO FARE PONTE A 2 JUMPER VICINI O ALLA PILA O ALLA EPROM.
ORA VEDRò IL MANUALE E QUINDI PROVO.
CHI VOLESSE DARGLI UN OKKIO E AIUTARMI QUI PUO TROVARE IL MANUALE
http://www.tcommate.com.tw/en/support_en/e-manual.htm
LA SCHEDA è LA K7TA
2.1.2 pulire il CMOS (Jumper giallo)
JRTC : CMOS Function Selection
1-2 : Clear data
2-3 : Normal Operation (Default Setting)
How to Clear the CMOS Setting:
Turn off the power.
Remove ATX power cable from power connector.
Remove Yellow Jumper Cap from JRTC (2-3) and put on JRTC (1-2)to remove the CMOS setting.
Remove Yellow Jumper Cap from JRTC (1-2) and put on JRTC (2-3).
Connect ATX power cable back to power connector.
Turn on the power.
While the system reboots, press key to set the BIOS setup
OK OK, in effetti ho risolto.
i primi 2 tentativi sono andati male, il 3° l'ho lasciato circa 25/30 min, e poi sono tornato, ho rispostato il jumper alla sez normale e quindi ..... è andato.
Ma la mia curiosità non si da pace.
com'è che le mie memorie sono da 133, ed impostando il 133/33 si è tutto impallato?
come dice lo stesso manuale: must install 7ns or faster SDRAM on board if you set 133/33 ~ 140/35MHz as external frequency
Ora, dato che 1/133000000 =7.51 alla -9 cioè 7.5 nano secondi non mi spiego il fatto!!!
vediamo chi mi sa dare una risposta plausibile.
a, cmqe scrivo dal mio amatissimo Athlon 800@824 (sta iniziando il mio overk) e il bios è OK!!!
Scritto Da - yhedarkenemy on 02 Ottobre 2002 08:01:33
qual'è il chipset della mobo?
mica il kt133?
se è lui probabilmente è lui che nn regge il 133 (chissà perchè l'hanno chiamato così?)
che cpu hai?
Athlon 800, Ordering Codes
K7TA Uses VIA VT8363 & VT82C686A chipset. Supports AMD Socket A 200MHz FSB CPU. Supports Ultra DMA 33/66.
1.1 Product Overview
Thank you for purchasing the K7TA, K7TA-H or K7TA266 motherboard. This motherboard utilizes VIA's latest technology, namely KT133 or KT133A chipset : VT8363 or VT8363A & VT82C686A or VT82C686B chipset. We have conducted a motherboard compatibility test with a variety of hardware and software, such as CPUs, memory, display cards, CD ROMs, Novell, MS Office...etc and compliance with Year 2000.
We have set high standards on our quality control, with absolute confidence, we believe this product is the wisest choice.
This manual is composed of four sections. The first section is the introduction of this motherboard, and the second section explains the proper procedure to setup the motherboard, the third section provides information on how to setup the CMOS. The last section states the installation for driver and utility.
Dunque come vedi è quello!!!
stacca (se c'è) il dissy sul northbridge e leggi se è un kt133 o un kt133A...se è il primo probabilmente è quello!!
è sicuramente il kt133, visto che il bus dichiarato è 200 e nn 266 come per il kt133a;
puoi provare a staccare il dissi e metterne uno maggiorato, ma è difficile che regga i 133 di bus. ciò nn toglie che potrebbe essere il processore a nn reggere..
il mio consiglio è quello di cambiare mobo, ci sono dei modelli ecs molto economici..
ciao!
Non c'è problema, x adesso tengo questa e lavoro sui 100, 103, 105, 107 ecc fino ad arrivare ad un overk da un 800 @ 880/900, il tanto che mi basta x ora!!
Lascio stare dal 133 in su!!!
Mobo x il mio TB athlon 800 non ne trovo in giro facilmente!!
e perchè mai vanno bene tutte le schede con socket A!
io ho un tb1400 su ecs con le ddr333..:D
si, ma che senso ha una con DDR 333 con un 800??
Fa ridere al solo raccontarlo....
memorie veloci fanno sempre di differenza anche a frequenze basse!
e poi puoi avventurarti ad overclockarlo per bene mettendo il bus a 133!
133*8=1064
che nn è impossibile!